brazerzkidaiap.blogg.se

1. #Orbit sprinkler controller manual
2. #Orbit sprinkler controller android
3. #Orbit sprinkler controller plus

There is also a 3/4″ conduit knockout in the event you wish to route your sprinkler control wire from behind. The back of the unit contains a bracket for a mounting screw at the top, and a location to drill out a hole for a second screw (bottom center). A 1/2″ knockout is provided here in case it is desired to run the power supply in a conduit (which is not required). The left hole is the pre-installed 120VAC power cord. You can simply run the wire through the existing hole, but knockouts are also provided for 1/2″ and 3/4″ conduit fittings. The bottom of the unit contains an opening to route the sprinkler control wiring (on the right in the pic above). I am not certain there is any control feature associated with those ports since there is no documentation provided on these, but it is likely that these provide continuous power. The controller comes with a jumper installed across these ports (removing the jumper will prevent the unit from working unless a sensor is connected).Īnd finally, two 24VAC terminals are provided to power any external rain or freeze sensor. There are two blue ports that can be used for a moisture or freeze sensor that will prevent the unit from running in rainy or freezing conditions. Also, some installations may not have city water, so in that case, this connection can be used to start an irrigation pump. The controller will open the master valve when any of the zones are running. Many municipalities require a master valve in the supply line downstream of the backwater valve as an additional protective feature and to limit water leakage. There are also two terminals labeled PUMP and COM that can be used to control a pump or a master valve (labeled MV on some other sprinkler controllers).

#Orbit sprinkler controller plus

There are 8 termination points with gray buttons for the 8 zones that this unit can control, numbered 1 through 8 plus a white COM port for the common wire. Then at the lower front of the unit underneath the removable panel are the wiring connections for the 24VAC supply to the sprinkler control valves. Fortunately, they placed these instructions on the inside of the removable cover for easy reference.

#Orbit sprinkler controller manual

It is the only manual control on the unit, which means that it requires a somewhat complex series of long and short single or double presses to control the unit. The “b” in the center is also a button that can be used for manual control of the unit.

Also, when the unit is irrigating, the three LED screens provide information about the operation the upper right screen displays the program, the lower right screen displays the remaining time, and the left screen displays the zone that is running.Īlso in the center of the controller is an LED-illuminated letter “b” surrounded by an LED-illuminated hexagonal ring. During setup, these screens will display different information. The lower right screen will display the next sprinkler start time, and the left screen will display the next sprinkler start date. In the normal operating mode with power on and the sprinklers not running, the upper right screen will display the current weather and the time (swapping between the two every four seconds). The front of the controller contains three small hexagon-shaped LED display screens that provide information, depending upon the mode of operation. The unit contains an easily removable cover to access the wiring connection ports. The unit is rated for indoor or outdoor installation with an IP65 rating which means it is completely dust-tight and rated for “low-pressure jets” of water directed from any angle (i.e. The B-HYVE XR that I received is for eight zones and is contained in a fairly ruggedly constructed plastic housing.

#Orbit sprinkler controller android

Android – Android version 5.0 and higher. What’s in the box?Īnd iPod Touch running iOS 13 and higher.

The controller is primarily operated from the app on your phone or other device, so it gives you control of your sprinkler system from anywhere. This controller is designed to operate an in-ground irrigation system with up to 8 or 16 zones (depending on the model), and also includes water-use monitoring, water conservation features, and WeatherSense programming. The B-HYVE XR is a Wi-Fi and Bluetooth-enabled sprinkler controller/timer that provides “smart” functionality through multiple programs to allow you to control when your sprinklers run and for how long.